Air Filter Housing Supports/Mounts

How-to's and repair secrets for your 4WD can be found here. Have a question? Ask it in here!
Post Reply
YoYoTercel
Member
Posts: 40
Joined: Fri Feb 10, 2017 5:29 pm
My tercel:: 1983 Tercel 4x4 SR5

Air Filter Housing Supports/Mounts

Post by YoYoTercel »

Found these rubber mounts for my Tercel Air filter housing. It fits pretty good. Before I had used stacks of rubber washers and it just looked ugly. Now the air filter housing is resting very firmly and probably has less vibration.
Tercel Supports.jpg

Found them on ebay.

https://www.ebay.com/itm/4-Amp-Case-Was ... SwKclZ3svt
You do not have the required permissions to view the files attached to this post.
User avatar
ARCHINSTL
Goldie Forever
Posts: 6369
Joined: Sat Apr 30, 2005 1:52 pm
My tercel:: Goldie is a 1986 SR5 attualmente con Weber/also owned the first T4WD in STL in late '82
Location: Kirkwood, a 'burb of St. Louis

Re: Air Filter Housing Supports/Mounts

Post by ARCHINSTL »

As reported in another thread, the PCV grommets are a perfect fit, and a heck of a lot cheaper!
Tom M.
T4WD augury?
"Oh, do not ask, 'What is it?' Let us go and make our visit."
T.S. Eliot - "The Love Song of J. Alfred Prufrock"
"Now and then we had a hope that, if we lived and were good, God would permit us to be pirates."
Mark Twain
The Professor
Highest Ranking Member
Posts: 650
Joined: Wed May 12, 2010 6:38 pm
My tercel:: 1987 Tercel SR5 4WD wagon
Location: Western Washington
Contact:

Re: Air Filter Housing Supports/Mounts

Post by The Professor »

I've used a short length of small diameter rubber hose split along its length, in a pinch.
1975 Subaru SuperStar wagon
1984 Subaru Turbo-Traction wagon & hardtop
1987 Subaru RX 3-door
1987 Subaru RX Type-RA 3-door
1987 Toyota Tercel SR5 wagon
1999 Subaru Forester S
2002 Subaru WRX sedan
2019 Subaru Outback 2.5i Limited
User avatar
Petros
Highest Ranking Member
Posts: 11930
Joined: Sun Jan 28, 2007 6:31 pm
My tercel:: '84 Tercel4wd w/extensive mods
Location: Arlington WA USA

Re: Air Filter Housing Supports/Mounts

Post by Petros »

I use the regular gromment on the bottom, and some old valve cover washer/gasket on the top, seems to hold it well. I always have old valve cover bolt seals sitting around.
'87 Tercel 4wd SR5 (current engine swap project)
'84 Tercel 4wd (daily driver, with on going mods)
'92 Mazda MPV 4wd (wife's daily driver)
'85 Tercel 4wd DLX auto(daughter's daily driver)
'01 Honda Civic (other daughter's daily driver)
Termell
Newbie
Posts: 21
Joined: Tue Apr 17, 2018 12:10 am
My tercel:: 1985 Tercel

Re: Air Filter Housing Supports/Mounts

Post by Termell »

YoYoTercel wrote: Thu Apr 26, 2018 2:12 pm Found these rubber mounts for my Tercel Air filter housing. It fits pretty good. Before I had used stacks of rubber washers and it just looked ugly. Now the air filter housing is resting very firmly and probably has less vibration.
Tercel Supports.jpg


Found them on ebay.

https://www.ebay.com/itm/4-Amp-Case-Was ... SwKclZ3svt
Looks perfectly fit. We might need one for the Tercel, we'll just finish the installation of rack and tonneau covers for the kayak mount on the truck. Thank you for the link.
Post Reply