Search found 227 matches
- Sat May 30, 2020 8:15 am
- Forum: Repair Guides
- Topic: Tachometer connection problem
- Replies: 8
- Views: 3765
Tachometer connection problem
My car is a Toyota Tercel 1987 DX Wagon. I wanted to connect a digital tachometer to measure the RPM of the engine. I connected the Battery terminals to the battery. I Connected the signal wire to the -ve end of the Starter coil (Coil Pack). Reading appears as 8888. Some times it shows 97,85, 100, 9...
- Thu May 28, 2020 1:52 am
- Forum: Tercel 4WD Repair Questions
- Topic: Car battery broken plate seen through the hole
- Replies: 9
- Views: 2947
Re: Car battery broken plate seen through the hole
We used to do it with safety precautions. In Sri Lanka, a new battery costs nearly one to half a months salary. Health risk is same when do change the acid. Old acid have ionic Lead. Should never pour them to area near to a cultivation or a water source. In most of the counties, battery service cent...
- Wed May 27, 2020 2:12 am
- Forum: Tercel 4WD Repair Questions
- Topic: Car battery broken plate seen through the hole
- Replies: 9
- Views: 2947
Re: Car battery broken plate seen through the hole
Mr. Petros, "Rapid charge and discharge" is the thing achieved by a trickle cell charger. In addition to that slow current also can do this as mentioned above. When plates are damaged, it is a simple way to repair it by cut open and replace plates. 1. Cut a rectangular area on the upper su...
- Mon May 25, 2020 8:06 pm
- Forum: Tercel 4WD Repair Questions
- Topic: Car battery broken plate seen through the hole
- Replies: 9
- Views: 2947
Re: Car battery broken plate seen through the hole
Mr. Petros. PbSO4 deposited on the plates are the problem when over-discharged . In such instances, I use 2A charger or a Trickle cell charger for 24 hour charging. Slow current and pulsate current can break down Lead Sulfate. When do the charging, charging stops at a one level and no advance in the...
- Sat May 23, 2020 10:02 pm
- Forum: Tercel 4WD Repair Questions
- Topic: Car battery broken plate seen through the hole
- Replies: 9
- Views: 2947
Re: Car battery broken plate seen through the hole
After cut and examine the cell, it could be noticed a heavy damage to the plates.
I accidentally charged the battery with closed caps. It could be the cause for such a damage to the 1 1/2 year old battery.
Replaced the cell with new plates and repaired.
Now battery works fine.
I accidentally charged the battery with closed caps. It could be the cause for such a damage to the 1 1/2 year old battery.
Replaced the cell with new plates and repaired.
Now battery works fine.
- Thu May 21, 2020 9:03 pm
- Forum: Tercel 4WD Repair Questions
- Topic: Car battery broken plate seen through the hole
- Replies: 9
- Views: 2947
Re: Car battery broken plate seen through the hole
Thank you very much Mr.Petros for your valuable answer. Should I check the voltage difference after attempt to crank? Before attempt to crank (just after charged),there are 2.2V - 2.3V in-between good cells. There is 1.9V between the bad cell and the adjacent good cell. After attempt to crank, there...
- Thu May 21, 2020 9:16 am
- Forum: Tercel 4WD Repair Questions
- Topic: Car battery broken plate seen through the hole
- Replies: 9
- Views: 2947
Car battery broken plate seen through the hole
My car is a Toyota Tercel 1987 DX Wagon. Car has a 65amp battery with 6 cells. When attempt to start, car only has the sound of the solenoid. Doesnt start. When I charge the batter, It charges upto 13.6 V. After attempt to crank, Battery voltage drops to 10.6V and that is kept steady. It dosnt comes...
- Sat Mar 14, 2020 9:04 am
- Forum: Tercel 4WD Repair Questions
- Topic: Body frame bar clips question
- Replies: 1
- Views: 1701
Body frame bar clips question
My car is a Toyota Tercel 1987 DX Wagon.
I want to make a add a gauge 12 frame bar clip.
Suggested solutions are cut gauge 12 bar or Adding double layer of gaude 18/16 clip.
Which is most suitable one among them.
I want to make a add a gauge 12 frame bar clip.
Suggested solutions are cut gauge 12 bar or Adding double layer of gaude 18/16 clip.
Which is most suitable one among them.
- Sun Mar 08, 2020 6:35 pm
- Forum: Tercel 4WD Repair Questions
- Topic: Body Frame main clips repair
- Replies: 2
- Views: 2442
Re: Body Frame main clips repair
Thank you for your valuable advice.
- Sat Mar 07, 2020 2:29 am
- Forum: Tercel 4WD Repair Questions
- Topic: Body Frame main clips repair
- Replies: 2
- Views: 2442
Body Frame main clips repair
My car is a Toyota Tercel 1987 DX Wagon. Body frame clips behind the left front wheel is damaged by some cause. It is made of gauge 18 sheet. What happens if I add a clip of gauge 12 (with more strength) like that is infront of the rear wheel which bears the lower arm? Main body frame is divided in ...
- Wed Feb 26, 2020 5:20 am
- Forum: Tercel 4WD Repair Questions
- Topic: Vacuum gauge rapid oscilation
- Replies: 7
- Views: 3308
Re: Vacuum gauge rapid oscilation
Again thank you Mr. Petros for your valuable advice.
- Mon Feb 24, 2020 4:54 am
- Forum: Tercel 4WD Repair Questions
- Topic: Vacuum gauge rapid oscilation
- Replies: 7
- Views: 3308
Re: Vacuum gauge rapid oscilation
No. Your advice had a critical point. Engine has a mild tickling sound. It is mentioned that tickling sound comes from either by valves or by contacts. Perhaps valves may have a problem.
- Sun Feb 23, 2020 6:19 am
- Forum: Tercel 4WD Repair Questions
- Topic: Vacuum gauge rapid oscilation
- Replies: 7
- Views: 3308
Re: Vacuum gauge rapid oscilation
Yes when RPM exceeds vibrating range drops to 18-16 range.
Problem is If the valve guides are worn, compression should be dropped. Isnt it?
Problem is If the valve guides are worn, compression should be dropped. Isnt it?
- Sat Feb 22, 2020 11:18 am
- Forum: Tercel 4WD Repair Questions
- Topic: Vacuum gauge rapid oscilation
- Replies: 7
- Views: 3308
Vacuum gauge rapid oscilation
My car is a Toyota Tercel 1987 DX Wagon with 3A engine. My car engine sound is smooth but not upto the expected level. So I tested the manifold vacuum. There is a rapid oscillation of the needle between 17 and 13 inhg. So I have done a compression test. All the cylinders had 150 psi (desired range w...
- Sat Feb 22, 2020 11:06 am
- Forum: Tercel 4WD Repair Questions
- Topic: Clutch alignment tool
- Replies: 8
- Views: 3877
Re: Clutch alignment tool
I have got made a Input shaft like thing with wood from a lathe worker.
I brought the clutch plate to him with the inner diameter measurement of the bearing. (Also a piece of wood)
I think it could have been better if made from iron.
I brought the clutch plate to him with the inner diameter measurement of the bearing. (Also a piece of wood)
I think it could have been better if made from iron.