Tercel4WD.com

https://i.imgur.com/mjlav8Q.jpg

I wanted to show off my custom seat solution for my '85 Tercel 4WD!
Found these killer Mk1a AW11 MR2 seats from a gentleman in California.
To fit in the tercel, I cut the stock seat brackets off at the rivets, took some measurements and transplanted those stock ...

It's funny, I've been thinking... if I had not spent all of these hours into cleaning that transmission, my crossmember and other parts, I could be done with the swap by now lol.

https://i.imgur.com/GyPB3TP.jpg
I am just about done cleaning up my manual transmission/front diff, ready to start piecing my car back together! I've still got the engine to do a little bit of a checkup/refresh on but that should be easy enough. Just replacing some gaskets etc.

https://i.imgur ...

Hello Tercel freaks,

I wanted to return to this topic once more with some information I gathered during a manufacturing process course at Arizona State. I took a materials science/manufacturing tech elective and additive manufacturing was one of our discussed topics. The professor mentioned that in ...

rer233 wrote: Tue Nov 15, 2022 12:58 pm All you gotta do is install the front half of the driveshaft, and you're good to go! (Trust me, I've done it.)

Right on! Thank you for confirming my suspicions.

The relay I photographed was under the kick panel near the fuse box. I honestly don't remember what it's function was anymore.


Ah, I'll have to check the kick panel location next time I am at the parts car, thanks.
No worries, I'll have another look through the forum info here - maybe its ...

.

Hi eightfive4WD. It's been so long since I did that conversion. I seem to remember the car wouldn't crank until that relay was installed but I'm not sure anymore.
For the wiring harness, both the automatic and standard plug into the same connector in front of the distributor. I did not have to do ...

http://i1063.photobucket.com/albums/t508/marlinh/008-1.jpg

Tunnel I cut from donor car, placed for tracing.

http://i1063.photobucket.com/albums/t508/marlinh/009.jpg

Holes roughed out. Did some extra grinding before final assembly.

http://i1063.photobucket.com/albums/t508/marlinh/064.jpg ...

https://i.imgur.com/yAbjPID.jpg
Well, all that's left to do is everything. I've got my main prize removed from my parts car.
https://i.imgur.com/ZZ74cAo.jpg
I've been reading through the posts here about cutting out & stitching in the transmission tunnel.
My issue is spacing, I want to make sure ...

I completed the 'sex change' operation on my '87 a/t car a couple months ago. Like you noted, the a/t floorpan seemed too "wimpy" to support the 4wd shifter and the whole top of the floorpan was shaped differently, so i cut it out of the donor car and screwed and glued it into the '87. The ...

http://i1063.photobucket.com/albums/t508/marlinh/070-1.jpg

The green relay on the top right is what I swapped from the manual donor car to the automatic. There is a space on the relay panel for it. The only other wiring to do is connect or jumper the safety switch at the pedal. The wiring ...

1983 sr5 everything except drive train is up for grabs. i want all these parts to go to use so im going to sell cheap, just make it worth my efforts. located in iowa if that helps figure shipping guess.


Hello,
I'd like to purchase the center console, as well as the inclinometer if it's still ...

I've bookmarked several more that are helpful for Weber set up and info. I recommend bookmarking these:

Installing a Weber Carb
https://tercel4wd.com/forums/viewtopic.php?t=1112
32/36 DGEV Weber carburetors
https://tercel4wd.com/forums/viewtopic.php?f=7&t=1021
Custom Weber 32/36 EGR Setup Info ...

Hi, When I was previously perusing posts I found one on good vacuum set-up for Weber carb. Now that I actually want to refer to it to see if I can improve how the vacuum on my car is arranged I haven't found it. Does anyone know where it is? Or a good way to quickly find it? If I search "Weber ...