Tercel4WD.com

Check the battery voltage while it's running at idle in neutral. If its above 15 volts, the light can come on to warn you that the battery is suffering.

For anyone considering this task, Mr Wrench has a great video with part numbers:
https://youtu.be/h11_au9vYek?si=Y06_Rj05YnQ74z4d

You might have a couple issues to sort out... maybe fuel and ignition. Does it run OK when the engine is cold? My first wagon had a similar problem that turned out to be ignition. It would run fine until warmed up, then sputter out and not restart until it cooled off. I swapped distributors and all ...

I never gave this much thought before I saw this post. I think I'll pull the rotor off and take a peek behind the grease stopper.

Here's a couple tech articles about the VV carb that may be helpful... not sure if the "field fix kit" mentioned is available anymore, but the articles describe some of the controls and how they work. http://www.mastertechmag.com/pdf/1992/11nov/199211IS_ToyotaVariableVenturi.pdf https://au...

That's low miles for an '87! I'm not familiar with the variable venturi carb, but some quick reading makes it sound nightmarish. I stumbled on this weber conversion kit that might interest you: https://www.ebay.com/p/4034806606 Seems like a chunk of cash, but it might be a big improvement over a pot...

I finally got around to try a carb swap, and got to see which gasket I was using: 20240317_100603.jpg The vacuum passage bolt and secondary vacuum port need to remain open to sample manifold vacuum as pictured. I thought the 21980 heater was built into the insulator, but I see now it's cemented in p...

Hi Zack... Maybe these bolt extractors would grab it https://www.lowes.com/pd/IRWIN-BOLT-GRIP-5-Pack-Bolt-Extractor-Set/1003021030 I used them successfully on some stripped allen head bolts. I agree with Mark's assessment. If they sweared over the bolt, it's probably cursed... I would pray over it a...

My bad... I was thinking T4WD. My '83 had the carburetor feedback system and my '88 has it too. FSM says USA Vehicles and Canada 3A-C Engine 4-Speed & Wagon A/T. I found this diagram that might be helpful to the owner of the '82 Corolla Tercel. I see it uses a mixture control valve, which just l...

The stock carb relies on "computer" controlled air bleeds (EBCV) to maintain optimal mixture based on oxygen sensor signal. So the default rich mixture is leaned out based on conditions. The advantage to retaining the stock controls is compensation for temperature and altitude. If you stud...

Could these be early "low impedance" injectors? This article has an interesting section on injector outputs:
https://marstechnicalsolutions.com/blog ... ng-the-4-0

Here's a diagram I found on the lakelandtoyota site. It appears to show two different options on the lower right. MF2899K.jpg The gasket with the tail off the secondary matches the shape of the insulator, as dlb indicated. The other option is open between the primary and secondary barrels, and also ...

Toyota part #90913-05018. Part name code 13801C. Shown as "discontinued" by various suppliers. While replacing a head gasket, found a few that had overtightened locknuts. I installed Honda D15B engine adjusters, since I had an old cylinder head available. 20240103_191621.jpg The 3AC hardwa...

That is unfortunate. Tell her insurance company you want the car replaced. Find similar examples for sale, or recently sold to justify the value. You don't have to accept their initial low ball offer. They might even try to get you to accept partial responsibility for the accident as a condition of ...

These are junkyard steelies that came with 195-65 14 snow tires. I tried striping with a Mack long liner brush... painted the emblems too. I always liked the look of Nascar steelies.